Dodge Journey: Seal, input flange

REMOVAL

Differential and Driveline
Fig. 80: Removing /Installing Propeller Shaft

NOTE: Rubber coupler is part of the propeller shaft assembly. Removing coupler from propeller shaft will result in vibration/balance issues.

1. Raise vehicle on hoist.

2. Apply alignment index marks (4) on the rear axle flange (5) and rubber coupler (1).

3. Remove three rear propeller shaft rubber coupler to rear axle input flange retaining bolts (3).

4. Slide propeller shaft (2) back off rear axle input flange (5) and move out of the way as needed.

Differential and Driveline
Fig. 81: Pinion Flange Nut Removal/Installation

5. Using tool C-3281 (1), loosen input flange nut.

Differential and Driveline
Fig. 82: Input Flange Nut Removal/Installation

  1. - NUT

6. Remove input flange nut (1), and discard.

Differential and Driveline
Fig. 83: Input Flange Washer

  1. - WASHER

7. Remove input flange washer (1).

Differential and Driveline
Fig. 84: Suitable Puller & Input Flange

8. Using suitable puller (2), remove input flange (1).

Differential and Driveline
Fig. 85: Input Flange Seal Removal/Installation

  1. - SEAL
  2. - SCREWDRIVER

9. Using suitable screwdriver (2), remove input flange seal from overrunning clutch housing.

INSTALLATION

Differential and Driveline
Fig. 86: Clutch Case

1. Using tool 9231A (1), install input flange seal to overrunning clutch case (2).

Differential and Driveline
Fig. 87: Input Flange Shaft Seal

2. Install input flange shaft seal (1), on shaft threads at midway point of threads (2).

Differential and Driveline
Fig. 88: Input Flange Removal/Installation

  1. - INPUT FLANGE

3. Install input flange (1).

Differential and Driveline
Fig. 89: Input Flange Washer

  1. - WASHER

4. Install flange washer (1).

Differential and Driveline
Fig. 90: Input Flange Nut Removal/Installation

  1. - NUT

5. Install new flange nut (1).

Differential and Driveline
Fig. 91: Pinion Flange Nut Removal/Installation

6. Using tool C-3281 (2), torque flange nut to 135 N.m (100 ft. lbs.).

Differential and Driveline
Fig. 92: Removing /Installing Propeller Shaft

7. Align marks (4) on propeller shaft rubber coupler (1) to rear axle input flange (5).

8. Install three rear propeller shaft to rear axle retaining bolts (3) and tighten to 58 N.m (43 ft. lbs.).

9. Lower vehicle.

    Fluid, differential
    Standard Procedure STANDARD PROCEDURE - DIFFERENTIAL ASSEMBLY FLUID CHANGE Fig. 79: Differential Assembly Fluid Change The drain plug (2) for the differential assembly is located in the bottom of ...

    Seal, output flange
    REMOVAL Fig. 93: Axle Seal Removal - SEAL - SCREWDRIVER 1. Raise vehicle on hoist. 2. Remove rear driveline module. 3. Use suitable screwdriver (2) to remove output seal (1). INSTA ...

    See also:

    INSTRUMENT CLUSTER DESCRIPTIONS
    1. Coolant Temperature Gauge The temperature gauge indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operating satisfactorily. The gaug ...

    Installation
    HOUSING-AIR DISTRIBUTION NOTE: LHD model shown in illustrations. RHD model similar. Fig. 131: Air Distribution Housing-Removal/Installation 1. Position the air distribution housing (2) onto ...

    Cable, shift
    REMOVAL Fig. 306: Identifying Knee Blocker 1. Remove the knee blocker (2). Fig. 307: Identifying Shift Cable At Shifter NOTE: Ensure the lock tab on the shift cable (2) is depressed before ...

    0.0088